Crown XLS802D Power Amplifier (1600 Watts)

Crown XLS802D Power Amplifier (1600 Watts)

Features:
Reliable design incorporates many popular features

Housed in a rugged, all-steel 2U chassis

Efficient forced-air fans prevent excessive thermal buildup

Electronically balanced XLR inputs; touchproof binding post and Speakon

Same Day Music is an authorized dealer of Crown products.

Performance
Power (1 kHz*):
8 ohms: 500W
4 ohms: 800W
2 ohms: 1050W
8 ohms bridged to mono: 1600W
4 ohms bridged to mono: 2100W

*1 kHz Power: refers to maximum average power in watts at 1 kHz with 0.5% THD.

Sensitivity (volts RMS) for full rated power at 4 ohms: 1.25 V

Frequency Response (at 1 watt) 22 Hz to 20 kHz: +0 dB, +0.8 dB

Signal-to-Noise Ratio (20 Hz to 20 kHz)
A-weighted, below rated power: >98 dB
No weighting, below rated power: >93 dB

Total Harmonic Distortion (THD): <0.5%

Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) from full rated output to +40 dB: < 0.3%

Damping Factor (8 ohm) 10 Hz to 400 Hz: >200

Crosstalk (below rated power) at 1 kHz: +76 dB. at 20 kHz: +58 dB

Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced

Load Impedance: Rated for 2 to 8 ohms per channel in Stereo, 4 to 8 ohms in Bridge Mono

AC Line Voltage and Frequency Configurations Available (+/-10%): 120 VAC 60 Hz, 100 VAC 50/60 Hz, 220 VAC 50 Hz, and 230-240 VAC

Controls
Level: 2 front-panel rotary level controls, 1 for each channel

Power: Front-panel switch; on when in the IN position

Circuit Breaker: Back-panel breaker provides overload protection

Mode Switch: Back-panel switch selects Dual or Bridge-Mono mode

Indicators
Signal Presence Indicators: 2 green LEDs, one for each channel, illuminate when the channel's input signal exceeds +40 dBu

Clip Indicators: 2 red LEDs, 1 for each channel, illuminate when the channel's output is being overdriven

Power Indicator: Blue LED indicates amplifier has been turned on and AC power is available

Fault Indicator: 2 red LEDs illuminate when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on

Input/Output
Input Connectors: 1 per channel; back-panel 3-pin female XLR input connectors

Output Connectors: Two 4-Pole Speakon Output Connectors accept 2-pole or 4-pole Speakon connectors. The top Speakon connector is wired for both channels so it can be used for bridge-mono wiring or for stereo wiring of two speakers to a single Speakon connector. One pair of back-panel binding posts per channel; accepts banana plugs or bare wire. (European models do not accept banana plugs.)

Protection
XLS Series amplifiers provide extensive protection and diagnostic capabilities, including output current limiting, DC protection, circuit breaker, and thermal protection.

Construction
Ventilation: Flow-through ventilation from front to back

Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation

Air Volume Requirements (per minute per unit): 80.15 cubic ft.

Dimensions: EIA Standard 19 in. (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height and 15.2 in. (38.6-cm) depth

Net Weight: 35.5 lb (16.1 kg)

Shipping Weight: 40.5 lb (18.4 kg)

Same Day Music is an authorized dealer of Crown products.

Efficient, powerful, affordable@Forced-air cooling@Detented level controls@XLR inputs, binding post and Speakon outputs@500 watts per channel at 8 ohms

Same Day Music is an authorized dealer of Crown products.

3 users have rated this product, but no one has reviewed it yet. To rate this item and/or write a review, click the "Rate It" button.